Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub

Or Book Technician Here


We've noticed this post involving A Step-by-Step Guide to Installing a Bathtub below on the web and thought it made sense to discuss it with you on this site.


A Step-by-Step Guide to Installing a Bathtub
Setting up a bath tub isn't exactly brain surgery, yet it does call for strong plumbing, carpentry, and also sometimes, tiling skills. Changing an old tub with a new one is also a moderately challenging job. If the old bathtub is readily obtainable, the project can relocate speedily; if you have to open a wall to get rid of the old tub and place the brand-new bathtub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Ensure you have qualified yourself for the task and are comfortable attempting it. Rather than employing a service provider to take control of a halfway-completed project, it is better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This article will certainly assist you mount a brand-new bath tub in your shower room if you have actually already purchased a brand-new tub and do not need to change the plan of your previous water system pipes.
Your tools as well as material list ought to comprise the following:


  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Flexible Wrench

  • Putty Knife

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  •  

Preparing for the Installment


Firstly, the sustaining structure supplied with the bath should be fitted (if called for) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the adaptable tap adapters to the bottom of both faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the versatile overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bathroom ought to currently be ready to be suited its last position.



Removing Old Touches


If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is detach the water. After doing so, turn on the taps to drain any water remaining in the system. The process of getting rid of the existing faucets can be rather problematic as a result of the restricted accessibility that is often the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a fabric prepared for the staying water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is needed for the new faucets to fit.



Mounting the Bathtub


Making use of both wood boards under its feet, place the tub in the called for position. The wooden boards are handy in evenly spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four tiny points.
The next objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the tub till the level reviews level.
To install faucets, fit all-time low of the furthest versatile tap connector to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
Activate the water as well as inspect all joints as well as brand-new pipework for leakages and also tighten them if required. Load the bathtub and also check the overflow electrical outlet as well as the typical outlet for leakages.
Finally, take care of the bathroom paneling as described in the maker's user's manual. Tiling and securing around the bath tub must wait till the bathtub has actually been utilized a minimum of when as this will resolve it right into its final position.



Fitting New Touches


If the tails of the brand-new faucets are plastic, then you will need a plastic connector to avoid damages to the thread. One end of the connector fits on the plastic tail of the faucet and the other end provides a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washing machines are in area between the faucet and also the sink. Secure the tap in place with the supplier supplied backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by using corrugated copper piping or with typical faucet adapters. The previous type must be linked to the faucet ends first, tightening up just by hand. The supply pipes can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been attached.



Tiling Around the Tub


In the location where the bathroom meets the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is very important as the installation can move sufficient to crack an inflexible seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with moisture as well as possible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and fittings. They are offered in tubes as well as cartridges, as well as can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill, you can fill it with twists of drenched newspaper or soft rope. Remember to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub is in usage. The sealant can crack rather very early if you do not consider this movement before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also easily readily available on the market. It is advisable to fit the ceramic tiles using waterproof or waterproof sticky and also cement.


A Step-by-Step Guide to Installing a Bathtub


Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


Remove the Existing Bathtub


To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


Choose the Right Bathtub


The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


Install the Plumbing and Ledger Board


You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


Install the Bathtub


When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


Hook up the Plumbing


Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


Install the Bathtub Surround


A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


A Step-by-Step Guide to Installing a Bathtub


As a serious person who reads on How to Install a Bathtub, I imagined sharing that piece of content was a great idea. For those who enjoyed our post plz don't forget to pass it around. I cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


Expertise? Call us!

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub”

Leave a Reply

Gravatar